Routers
Router
Festool OF 1400 EBQ-Plus GB 240V
Collets
Ø 1/4" clamping collet (6.35 mm) 
Ø 1/2" clamping collet (12.7 mm)
OF1010 Copying Rings / Guide Bushes
D 10.8 Ø 7.8mm KR-D 10.8/OF 900 - 486029
D 13.8mm Ø 10.8mm KR-D 13.8/OF 900 - 484176
D 17mm Ø 14mm KR-D 17/OF 900 - 486030
D 24mm Ø 21mm KR-D 24/OF 900 - 486031
D 27mm Ø 24mm KR-D 27/OF 900 - 486032
D 30mm Ø 27mm KR-D 30/OF 900 - 486033
D 40mm
Ø 37mm KR-D 40/OF 900 - 486034
OF1400 Copying Rings / Guide Bushes
D 17 mm Ø 14 mm KR-D 17,0/OF 1400 - 493315 Required for morticing with 12.7mm / 1/2” bit
D 24 mm Ø 21 mm KR-D 24,0/OF 1400 - 492183
D 27 mm Ø 24 mm KR-D 27,0/OF 1400 - 492184
D 30 mm Ø 27 mm KR-D 30,0/OF 1400 - 492185
D 40 mm Ø 37 mm KR-D 40,0/OF 1400 - 492186
Rabbeting - Adjustable
- 18mm cutting depth, 1/2” shank, 38mm diameter, up sheer (6mm to 15mm rebate depending on bearing) Wealden T1714-1/2
Bearings
- Wealden TB885 6.0mm Rebate with T1714-1/2
- Wealden TB452 
Down Shear Trim
Double bearing guided cutter has two down-shear cutting blades which ensure a clean cut even in difficult materials. In addition, the positive shear angle reduces breakout on the top edge, making it ideal for trimming veneered board. The two bearing design allows the cutter to be used with the template mounted on either side of the work and, consequently, it is possible to cut from either direction using only one template and without moving the template to the other side of the workpiece. This is especially useful when cutting curves which run both with and against the grain.
- 19.0mm diameter - 1/2" shank, 50mm cutting depth (Wealden T8175B-1/2) £33.25
Chamfer
- 14.6mm 20mm 1/2 40mm 42mm 20mm (Wealden T916B 1/2)
Straight Fluted
- 4mm / 5/32” diameter - 1/4” shank, 11mm cutting depth (Wealden T204W)
- 9.5mm / 3/8” diameter - 1/2” shank, 30mm cutting depth (Wealden T1409.5M)
- 12.7mm / 1/2” diameter - 1/2” shank, 35mm cutting depth (Wealden T1412.7M)
Panel Trim
- Wealden T8012B Panel Trim
Ovolo - Round Over - Wealden T1325 2.5mm 10mm 1/4 28mm 18.0mm TB394 + TB452 Bearing? to roundover workbench
Pondering...
Down-Cut Spiral, 12.70mm 50mm 1/2" 106mm TB500 T2DT1270 £85.20
1 £11.36 £11.36 1 £9.42 £9.42
| Part No. | Type | Body | Shank | Notes | Link | |||||
|---|---|---|---|---|---|---|---|---|---|---|
| Thickness | Dia. | Dia. | Length | |||||||
| mm | inch | |||||||||
| Wealden | T1714-1/2 | Rabbeting | 18mm | 38.0 | 1/2" | 40mm | Up shear. Can be used with guide bearings | Wealden | |
|
| T204W | Straight Two Flute | 11mm | 4.0 | 5/32" | 1/4" | 38mm | A range of straight cutters which are all two flute except T201W and T201.5S marked ## which are a single flute with Solid TC cutting blades. These general purpose cutters are suitable for grooving, dadoing, rabbeting etc. Please note the comments in the "using the router" section under the "Safe Use" menu item. Particular care should be taken when using long series cutters. All sizes are suitable for plunge cutting, with sizes above 9mm diameter having an additional centre carbide tip to ensure a faster and cleaner cut when plunging. When selecting cutters always choose the shortest cutter that will give the depth you require. Shorter bits cut cleaner with less noise and give a longer life. | Wealden | |
|
| T204.8W | 11mm | 4.8 | 3/16" | 1/4" | 38mm | |
||||
| T1409.5M | 30mm | 9.5 | 3/8" | 1/2" | 40mm | A range of straight two flute cutters in 1/2 inch shank. These general purpose cutters are suitable for grooving, dadoing, rabbeting etc. Please note the comments in the 'using the router' section under the 'Safe Use' menu item. Particular care should be taken when using long series cutters. All sizes except T1409.5R are suitable for plunge cutting, with sizes above 9mm diameter having an additional centre carbide tip to ensure a faster and cleaner cut when plunging. When selecting cutters always choose the shortest cutter that will give the depth you require. Shorter bits cut cleaner with less noise and give a longer life. | Wealden | |
||
| T210M 10.0 25/64 20mm 1/4" 38mm £10.03 | ||||||||||
| T1412.7M | 35mm | 12.7 | 1/2 | 1/2" | 40mm | |
||||
| T2U1000L | Down Cut 2 Flute | 40.0 | 10.0 | 25/64 | 1/2 | 40? | A range of high quality micro-grain 2 flute solid carbide spiral upcut cutters primarily intended for use in CNC and fixed head routing machines. These specialist cutters offer high performance routing, with fine finish and high feed rates being prime advantages over straight flute cutters. In cases where carbide tip tools perform well, spiral routers will cut smoother and generally last up to 5 times longer. This extra tool life means fewer tool changes, less setup time and longer production runs. The cutters are suitable for use at speeds of 17,000 to 25,000 rpm and with feed rates of 3 to 10 metres per minute. It should be noted that the most common reason for premature wear is insufficient feed rates and worn collets are the main cause of tool breakage. | Wealden | 29.01/21 |
|
| T8012B | Panel Trim | 25mm | 6.35 | - | 1/4" | 38mm | Bottom bearing guided two flute cutter for trimming and profiling to a template. May also be used as a low cost trimmer for laminates, veneering, edge banding etc. | Wealden | |
|
| T914B | 45 Degree Chamfer | 11mm | 24.0 | - | 1/4" | 38mm | Two flute cutter with guide bearing to produce chamfered edges. Used for relieving edges on frames, legs, sills, mouldings etc. Stopped chamfers can be an attractive decoration for beams, gates etc. | Wealden | Paulk |
|
| T916B-1/2 | 20mm | 42.0 | - | 1/2" | 36mm | |
||||
| TB885 | Bearing | 26.0 | Bearings | Wealden | |
|||||
| TK1714 | |
|||||||||
| Axcaliber | 101972 | T Slot Cutter | |
|||||||
Festool MFS
- Routing Template MFS 400 (492610) for rectangular (300x100mm) or curved (40-600mm dia) cut outs.
Festool MFS 700 Routing Template for rectangular (max. 600 x 300 mm) or curved (max. Ø 1200 mm) cut-outs.
Aperture = cut size + guide bush (30) - router bit size
Collection
Wanted